Publications

(A). BOOKS AUTHORED

1.    Singh, H. and Prakash, S., 2009, Plasma Spray Coatings for Superalloys, VDM Publishing House, Germany.

 (B). CHAPTERS IN BOOK

1.    Singh, H. and Dhindaw, B. K., 2011, Metal Matrix Composites: Aluminum in Handbook of Composites, Wiley.
2.    Rubrecht, S., Singla, E., Padois, V., Bidaud, P., and Broissia, M., 2010, "Evolutionary design of a robotic manipulator for a highly constrained environment". Exploring New Horizons in Evolutionary Design of Robots, Editors: S. Doncieux, J-B. Mouret, N. Bredeche, Springer-Verlag.

 

(C). BOOKS EDITED

1.    A book on "Inorganic Matrix Composites" edited by Prof. M. K. Surappa has been published by The Minerals, Metals & Materials Society of USA (1996).

 

(D.) RESEARCH PAPERS PUBLISHED IN REFEREED JOURNALS

2013

 

1.  Anilchandra, A. R., & Surappa, M. K., 2013, "Microstructure And Tensile Properties Of Consolidated Magnesium Chips", Materials Science and Engineering A, Vol. 560, pp. 759-766. 

 

2.  Agarwal, A.K., Srivastava,D.K., Dhar, A., Maurya, R.K., Shukla, P.C, and  Singh, A.P., September 2013, “Effect of Fuel Injection Timing and Pressure on Combustion, Emissions and Performance Characteristics of a Single Cylinder Diesel Engine”,Fuel,Volume 111,Pages 374–383, 2013 (ISSN: 0016-2361). (Impact Factor: 3.357)

 

3.   Agarwal, A.K., Srivastava,D.K., Dhar, A., Maurya, R.K., and  Singh, A.P., May 2013, “ Effect of Fuel Injection Pressure on Diesel Particulate Size and Number Distribution in a CRDI Single Cylinder Research Engine”,  Fuel,  Volume 107,  Pages 84–89,2013 (ISSN: 0016-2361). (Impact Factor: 3.357)

 

4.   Bhowmik, A., Singh, R., Repaka R., and Mishra,S.C. ,2013, ”Conventional and newly developed bioheat transport models in vascularized tissues - A review”, 38 p. 107-125, J. Therm. Biology.

 

5. Das, R., and K.T. Ooi 2013, Application of simulated annealing in a rectangular fin with variable heat transfer coefficient, Inverse Problems in Science & Engineering, (DOI: 10.1080/17415977.2013.764294).

 

6.   Das, R. and K.T. Ooi, 2013, Predicting multiple combination of parameters for designing a porous fin subjected to a given temperature requirement, Energy Conversion & Management, (in press).

 

7.       Das, R., 2013, Three parameter estimation studies in a radial fin geometry using FDM based simplex method, Heat Transfer Engineering, (in press).

8. Grewal, H.S., Singh, H., and Agrawal, A., 2013, “Understanding Liquid Impingement Erosion Behaviour of Nickel-Alumina Based Thermal Spray Coatings”, Wear, DOI: 10.1016/j.wear.2013.01.063  

9.   Grewal, H.S., Arora, H.S., Agrawal, A., and Singh, H., 2013, “Surface Modification of Hydroturbine Steel using Friction Stir Processing”, Appl. Surf. Sci., DOI: 10.1016/j.apsusc.

2013.01.006.

10.  Grewal, H.S., Singh, H., and Agrawal, A., 2013, “Microstructural and Mechanical Characterization of Nickel-Alumina Thermal Sprayed Coatings”, Surf. Coat. Technol., Vol. 216, pp. 78–  92.

11 Grewal, H.S., Agarwal, A., and Singh, H., 2013, “Design and Development of High-Velocity Slurry Erosion Test Rig using CFD”, J. Mater. Eng. Perform., Vol.   22,pp.152–161.

12.  Hojamberdiev,M., Prasad,R.M., Fasel,C., Riedel,R.,Ionescu,E.,“Single-sourceprecursor synthesis of soft magnetic Fe3Si- and Fe5Si3-containing SiOC ceramic nanocomposites,” Journal of the European Ceramic Society,vol.33 (2013),PP.2465-2472

13. Maurya, R.K., and  Agarwal, A.K., November  2013, “Experimental Investigation of Cyclic Variationsin HCCI Combustion Parameters for Gasoline like Fuels Using Statistical Methods” Applied Energy,Volume 111,  pp. 310-323, 2013 . (ISSN # 0306-2619). (Impact Factor: 4.781)

14.

Maurya, R.K.,and Agarwal, A.K., “Investigation on the effect of measurement errors on estimated combustion and performance parameters in HCCI combustion engine”, Measurement, Volume 46, Issue 1, pp, 80–88, 2013. (ISSN: 0263-2241). (Impact Factor: 1.130)

15. Maurya, R.K., Pal,D.D., and Agarwal, A.K., "Digital Signal Processing of Cylinder Pressure Data for Combustion Diagnostics of HCCI Engine" Mechanical Systems and Signal Processing, Volume 36, Issue 1, pp. 95–109, 2013. (ISSN # 0888-3270). (Impact Factor: 1.913)

16.  Maurya, R.K., and Agarwal, A.K., “Experimental Investigations of Gasoline HCCI Engine during Startup and Transients”, Accepted SAE International Journal of Engines, SAE 2011-01- 2445. (Print ISSN: 1946-3936; Online ISSN: 1946-3944).

17.  Pashchanka,M., Prasad,R.M., Hoffmann,R.C., Gurlo,A., Schneider,J.J.,“Inkjet printed nanoscaled CuO for miniaturized gas sensing devices,” European Journal of Inorganic Chemistry, 2013 pp.1481-1487

18.  Phelan, P., Otanicar, T., Taylor, R., & Tyagi, H., Jun 2013 "Trends and Opportunities in Direct-Absorption Solar Thermal Collectors”, ASME Journal of Thermal Science & Engineering  Applications, Vol. 5(2), p. 021003.

19. Shukla, A., Singla, E., Wahi, P., & Dasgupta, B., 2013, "A Direct Variational Method for Planning Monotonically Optimal Paths for Redundant Manipulators in Constrained Workspaces, Robotics and autonomous Systems, Vol. 61,  pp. 209 - 220.

20. Soni, S., Tyagi, H., Taylor, R. A., & Kumar, A., 2013, "Role of Optical Coefficients and Healthy Tissue Sparing Characteristics in Gold Nanorod Assisted Thermal Therapy”,        International Journal of Hyperthermia, Vol. 29(1), pp. 87-97, Feb 2013. (doi: http://dx.doi.org/10.3109/02656736.2012.753162)
 

21. Taylor, R., Coulombe, S., Otanicar, T., Phelan, P., Gunawan, A., Lv, W., Rosengarten, G., Prasher, R., & Tyagi, H., 2013, "Small Particles, Big Impacts: A Review of the Diverse Applications of Nanofluids”, Journal of Applied Physics, Vol. 113(1), pp. 011301, Jan 2013. [Invited]. (doi: http://dx.doi.org/10.1063/1.4754271)

 

2012

 

1.   Agrawal, A., Reddy, N. V., Dixit, P. M. 2012, “Prediction of Wrinkling and Determination of Minimum Blankholding Pressure in Multistage Deep Drawing”, Transactions of The ASME: Journal of Manufacturing Science and Engineering, 133(6),PP. 061023.

 

2.      Agrawal, A., Ziegert J., Smith, S., Woody, B. and Cao, J. 2012, “Study of Dimensional Repeatability and Fatigue Life for Deformation Machining Bending Mode”, accepted for publication in Transactions of The ASME: Journal of Manufacturing Science and Engineering.134(6),PP. 61009

 

3.    Anilchandra, A. R., Basu, R., Samajdar, I., Surappa, M. K., 2012, "Microstructure and Compression Behavior of Chip Consolidated Magnesium", Journal of Materials Research,  27(4), pp. 709-719.

 

4.     Anilchandra, A. R., & Surappa, M. K., 2012, "Microstructure and Damping Behaviour of Consolidated Magnesium Chips", Materials Science and Engineering A, 542, pp. 94-103ng

 

5.     Arora, H. S., Singh, H. and Dhindaw, B. K., 2012, “Numerical Simulation of Temperature Distribution using Finite Difference Equations and Estimation of the Grain Size during Friction Stir Processing”, Mater. Sci. Eng. A, . 543,(1), pp. 231–242.

6.       Arora, H. S., Singh, H. and Dhindaw, B. K., 2012, “Parametric Study of Friction Stir Processing of Magnesium Based AE42 Alloy”, J. Mater. Eng. Perfor., accepted for publication.21(11), pp. 2328-2339

7.     Arora, H. S., Singh, H. and Dhindaw, B. K., 2012, “Some Observations on Microstructural Changes in a Mg-based AE42 Alloy subjected to Friction Stir Processing”, Metall. Mater. Trans. B, Vol. 43 (1) , pp. 92-108

8.  Arora, H. S., Singh, H. and Dhindaw, B. K., 2012, “Corrosion Behaviour of a Mg Alloy AE42 Subjected to Friction Stir Processing”, Corros., DOI: 10.5006/0750.

9.      Bala, N., Singh, H. and Prakash, S., 2012, “Performance of Cold Sprayed Ni-20Cr and Ni-50Cr Coatings on SA 516 Steel in Actual Industrial Environment of a Coal Fired Boiler”, Mater. Corros., accepted for publication.

10. Bala, N., Singh, H., Prakash, S. and Karthikeyan, J., 2012, “Investigations on the Behavior of HVOF and Cold Sprayed Ni-20Cr Coating on T22 Boiler Steel in Actual Boiler Environment”, J. Thermal Spray Technol., 21(1), pp. 144-158.

11.  Bhandari, S., Singh, H., Kansal, H. K. and Rastogi, V., 2012, “Slurry Erosion Performance Study of Detonation Gun Sprayed WC-10Co-4Cr Coatings on CF8M Steel under Hydro- accelerated Conditions”, J. Thermal Spray Technol., accepted for publication.21 (5) , pp. 1054-1064

12. Bhandari, S., Singh, H., Kansal, H. K. and Rastogi, V., 2012, “Slurry Erosion Studies of Hydroturbine Steels under Hydro Accelerated Conditions”, Proc. Instn Mech. Engrs, Part J: J.  Eng. Tribology, Vol. 226, No. 3, pp. 239-250.

13.      Das, R., 2012, "Application of genetic algorithm for unknown parameter estimations in cylindrical fin", Applied Soft Computing, 12(11), pp. 3369-3378.

14.    Das, R., and Dutta, P. P., 2012, "Application of simulated annealing for simultaneous estimation of parameters in a cylindrical fin", Numerical Heat Transfer:   Part A, Vol. 61 (9), pp. 699-716.

15.  Das, R., 2012, "A simulated annealing-based inverse computational fluid dynamics model for unknown parameter estimation in fluid flow problem", International Journal of Computational Fluid Dynamics, 26 (9-10) , pp. 499-513 

16.     Das, R ., 2012, "Inverse analysis of Navier-Stokes equations using simplex search method, Inverse Problems in Science & Engineering",  20 (4), pp. 445-462.

17. Gill, S. S., Singh, J., Singh, H. and Singh, R., 2012, “Metallurgical and Mechanical Characteristics of Cryogenically Treated Tungsten Carbide (WC-Co)”, Inter. J.  Advanced Manufacturing Technol.,  58(1), pp. 119-131.

18.  Gill, S. S., Singh, R., Singh, J. and Singh, H., 2012, “Adaptive Neuro-Fuzzy Inference System Modeling of Cryogenically Treated AISI M2 HSS Turning Tool for Estimation of Flank Wear”, Expert Systems with Applications, Vol. 39, No. 4, pp. 4171-4180.

19.   Goyal, D., Singh, H., Kumar, H. and Sawhney, B.K., 2012, “Slurry Erosion Behaviour of HVOF Sprayed WC-10Co-4Cr and Al2O3 + 13TiO2 Coatings on Turbine Steel”, Wear, accepted for publication. 289 , pp. 46-57

20.   Goyal, D., Singh, H., Kumar, H. and Sawhney, B. K., 2012, “Slurry Erosive Wear Evaluation of HVOF-Spray Cr2O3 Coating on Some Turbine Steels”, J. Thermal Spray Technol., Vol. 21, pp. 838–851

21.   Grewal, H.S., Agarwal, A., Singh, H., 2012, “Design and Development of High-Velocity Slurry Erosion Test Rig using CFD”, J. Mater. Eng. Perfor., Journal of Materials Engineering and Performance 22 (1) , pp. 152-161

22.   Grewal H.S., Singh H., Agrawal A. 2012 “CFD Modeling for Evaluation of Slurry Erosion of Hydroturbine Materials”, International Journal of Advanced Mechatronics and Robotics,  3(2), pp. 61-70.

23.   Grewal, H.S., Bhandari, S., Singh, H., 2012, “Parametric Study of Slurry-Erosion of Hydroturbine Steels with and without Detonation Gun Spray Coatings using Taguchi Technique”, Metall. Mater. Trans. A, 43 (9) , pp. 3387-3401

24. Grewal, H. S., Singh, H., Agrawal, A. and Arora, H. S., 2012, “Friction Stir Processing of Mild Steel to Enhance its Surface Hardness”, Adv. Mater. Res., Vol. 620, pp. 117–121.

25. Hojamberdiev,M.,Prasad,R.M.,Morita,K., Zhu,Y., Schiavon,M.A., Gurlo,A.,Riedel,R., “Template-free synthesis of polymer-derived mesoporous SiOC/TiO2 and SiOC/N-doped TiO2 ceramic composites for application in the removal of organic dyes from contaminated water,” Applied Catalysis B: Environmental, pp.115-116 (2012)

26. Hojamberdiev,M.,Prasad,R.M.,Morita,K., Zhu,Y., Schiavon,M.A., Riedel,R., “Polymerderived mesoporous SiOC/ZnO nanocomposite for the purification of water contaminated  with       6organic dyes,”  Microporous and Mesoporous Materials, Vol. 151 (2012) pp. 330-338

27.   Kaur, M., Singh, H. and Prakash, S., 2012, “High-temperature Behavior of a High-Velocity Oxy-Fuel Sprayed Cr3C2-NiCr Coating”, Metall. Mater. Trans. A, Physical Metallurgy and Materials Science.43 (8) , pp. 2979-2993

28.  Kaur, M., Singh, H., and Prakash, S., 2012, “X-Ray Diffraction Study of HVOF Sprayed Cr3C2-NiCr Coating”, Adv. Mater. Res., Vol. 620, pp. 186–192

29. Kaushal, G., Singh, H. and Prakash, S., 2012, “Performance of Detonation Gun Sprayed Ni-20Cr Coating on ASTM A213 TP347H Steel in A Boiler Environment”, J. Thermal Spray Technol., 21 (5) , pp. 975-986

30.  Kaushal, G., Kaur, N., Singh, H. and Prakash, S., 2012, “Effect of Zirconium addition in HVOF-sprayed Ni-20Cr Coating”, Surf. Eng., DOI: 10.1179/1743294412Y.0000000051.

31. Kayhan,E., Prasad,R.M., Gurlo, A., Yilmazoglu,O., Pavlidis,D., Engstler,J.,  Ionescu,E., Yoon,S., Weidenkaff,A., Schneider,J.J.,  “Synthesis, characterization, electronic and gas sensing properties towards H2 and CO of transparent, large area,  low layer graphene, ” Chemistry - A European Journal,Vol. 18 (2012) pp.14996-15003.

32. Khullar, V. and Tyagi, H., 2012, "A Study on Environmental Impact of Nanofluid-Based Concentrating Solar Water Heating System", International Journal of Environmental Studies, Vol. 69(2), pp. 220-232.  (doi: http://dx.doi.org/10.1080/00207233.2012.663227)

33.  Khullar, V., Tyagi, H., Phelan, P. E., Otanicar, T. P., Singh, H., & Taylor, R. A., 2012, "Solar Energy Harvesting Using Nanofluids-Based Concentrating Solar Collector”, ASME Journal of Nanotechnology in Engineering & Medicine, Vol. 3(3), pp. 031003.  (doi: http://dx.doi.org/10.1115/1.4007387)

34. Kumar, N. and Singh, S. P., 2012, "Vibration Control of Curved Panel Using Smart Damping Mechanical Systems and Signal Processing",(Elsevier Journal, Impact factor, 2.471).30 , pp. 232-247

35. Kumar, N. and Pochiraju, K.,2012, "Dynamics of Virial Stress in Gold   Lattic after Crack Initiation, Proceedings of the Institution of Mechanical Engineers",Vol. 226 Part C: J. Mechanical Engineerting Science, , Page: 358-366.

36. Kumar. M., Singh. H. and Singh. N., 2012, “Extraction and Transport Behavior of Tripodal Receptor: Selective Recovery of Ni2+ and Processing into Nickel Nano-particles”, Mineral Processing and Extractive Metallurgy, DOI: 10.1179/1743285512Y.0000000030

37.  Mehandia, V., Gautam, J. K., & Nott, P. R., 2012, "Anomalous Stress Profile in Sheared Granular Column", Physical Review Letters, Vol. 109(12), p. 128002.

38.  Maurya, R.K.,and Agarwal, A.K., “Statistical Analysis of cyclic variation of Heat release parameters in HCCI combustion of Methanol and gasoline fuel”,  Applied Energy, Volume 89, Issue 1, January 2012, pp. 228-236, 2012. (ISSN # 0306-2619). (Impact Factor: 4.781)

39.  Prasad,R.M., Mera,G., Morita,K., Mueller,M., Kleebe,H.J., Gurlo,A., C. Fasel, Riedel,R., “Thermal decomposition of carbon-rich polymer-derived silicon carbonitrides leading to ceramics with high specific surface area and tunable micro- and mesoporosity,” Journal of the European Ceramic Society,Vol. 32 (2012) pp. 477-484

40. Singh, T. P., Singh, H. and Singh, H., 2012, “Characterization, Corrosion Resistance and Cell Response of High Velocity Flame Sprayed HA and HA/TiO2 Coatings on 316L SS”, J. Thermal Spray Technol., accepted for publication.

41. Singh, T. P., Singh, H. and Singh, H., 2012, “Characterization and In-Vitro Corrosion Investigations of Thermal Sprayed Hydroxyapatite and Hydroxyapatite-Titania Coatings on Ti-Alloy”, Metall. Mater. Trans. A,43 (11) , pp. 4365-4376.

42. Singh, T. P., Singh, H. and Singh, H., 2012, “Characterization of Thermal Sprayed Hydroxyapatite Coatings on Some Biomedical Implant Materials”, J. Appl. Biomater. Biomech., accepted for publication.

43.  Umbrello, D., Pu, Z., Caruso, S., Outeiro, J. C., Jayal, A. D., Dillon, O. D., and Jawahir, I. S., 2012, “The effects of Cryogenic Cooling on Surface Integrity in Hard Machining,” Procedia Engineering, 19, pp. 371-376. Also presented at 1st CIRP Conference on Surface Integrity (CSI), 30 Jan – 01 Feb 2012, Bremen, Germany.

44. Varunkumar, S., Rajan, N. K. S., & Mukunda, H. S., 2012, "Experimental and computational studies on a gasifier based stove", Energy Conversion and Management, Vol. 53(1), pp. 135-141.

 

 2011

1.   Arora, H. S., Singh, H. and Dhindaw, B. K., 2011, “Composite Fabrication using Friction Stir Processing - A Review”, Inter. J. Adv. Manu. Technol., accepted for publication.

2.   Bala, N., Singh, H. and Prakash, S., 2011, “Characterisation and High Temperature Oxidation Behaviour of Cold Sprayed Ni-20Cr and Ni-50Cr Coatings on Boiler Steels”, Metall. Mater. Trans. A, 42 (11) , pp. 3399-3416

3.    Bala, N., Singh, H. and Prakash, S., 2011, “Comparative Performance of Cold Sprayed Ni-20Cr and Ni-50Cr Coatings on T22 Boiler Steel in Different Aggressive Environments”, Inter, J. Surf. Eng. Mater. Technol., 1(1),  pp. 12-16.

4.   Bhandari, S., Singh, H., Kansal, H. K. and Rastogi, V., 2011, “Slurry Erosion Behaviour of Detonation Gun Spray Al2O3 and Al2O3-13TiO2 Coated CF8M Steel under Hydro- accelerated Conditions”, Tribology Lett., accepted for publication. 

5.   Caruso, S., Di Renzo, S., Umbrello, D., Jayal, A. D., Dillon, O. W., and Jawahir, I. S., 2011, “Finite Element Modeling of Microstructural Changes in Hard Turning,” Advanced Materials Research, 223, pp. 960-968. Also presented at 13th CIRP International Workshop on Modeling of Machining Operations, 12-13 May 2011, Sintra, Portugal, pp. 960-968.

6.   Das, R., 2011, A simplex search method for a conductive-convective fin with variable conductivity, International Journal of Heat & Mass Transfer,  54 (23-24), pp. 5001-5009.

7.    Das, R., 2011, Estimation of radius ratio in a fin using inverse CFD model, CFD Letters, 03 (1), pp. 40-47.

8.   Das, R., S.C. Mishra, T.B. Pavan Kumar and R. Uppaluri, 2011, An inverse analysis for parameter estimation applied to a non-Fourier conduction-radiation  problem, Heat Transfer Engineering,  32 (6), pp.455-466.

9.   Gill, S. S., Singh, J., Singh, R. and Singh, H., 2011, “Effect of Cryogenic Treatment on AISI M2 High Speed Steel–Metallurgical and Mechanical Characterization”, J. Mater. Eng. Perfor., accepted for publication.

10.   Gill, S. S., Singh, J., Singh, R. and Singh, H., 2011, “Metallurgical Principles of Cryogenically Treated Tool Steels- A Review on Current State of Science”, Inter. J. Advanced Manufacturing Technol., 54(1-4), pp. 59-82.  

11.  Goyal, D., Singh, H. and Kumar, H., 2011, “An Overview of Slurry Erosion Control by the Application of High Velocity Oxy Fuel Sprayed Coatings”, Proc. Instn Mech. Engrs, Part J: J. Eng. Tribology, 225(11), pp. 1092-1105.

12.   Jawahir, I. S., Brinksmeier, E., M’Saoubi, R., Aspinwall, D. K., Outeiro, J. C., Meyer, D., Umbrello, D., and Jayal, A. D., 2011, “Surface Integrity in Material Removal Processes: Recent Advances,” Keynote paper, Annals of the CIRP, 60(2), pp. 603-626.

13.    Kaur, M., Singh, H. and Prakash, S., 2011, “Studies on Role of Detonation-Gun Sprayed WC-Co Coatings to Combat High Temperature Corrosion of Boiler Steel”, Inter, J. Surf. Eng. Mater. Technol., 1(1), pp. 33-38.

14.    Kaur, M., Singh, H. and Prakash, S., 2011, “Surface Engineering Analysis of Detonation-gun Sprayed Cr3C2-NiCr Coating under High-Temperature Oxidation and Oxidation-Erosion Environments”, Surf. Coat. Technol., Vol. 206, pp. 530–541.

15.    Kaushal, G., Singh, H. and Prakash, S., 2011, “Comparative High Temperature Analysis of HVOF Sprayed and Detonation Gun Sprayed Ni-20Cr Coating in Laboratory and Actual Boiler Environments”, Oxidation of Metals, accepted for publication.

16.    Kaushal, G., Singh, H. and Prakash, S., 2011, “High Temperature Corrosion Behavior of HVOF- Sprayed Ni-20Cr Coating on Boiler Steel in Molten Salt Environment at 900ºC”, Inter. J. Surf. Sci. Eng., 5(5-6), pp. 415-433.

17.    Kaushal, G., Singh, H. and Prakash, S., 2011, “High Temperature Erosion-Corrosion Performance of HVOF sprayed Ni-20 Cr coating in Actual Boiler Environment”, Metall. Mater. Trans. A,  42, pp. 1836-1846.

18.    Kaushal, G., Singh, H. and Prakash, S., 2011, “Surface Engineering, by Detonation-Gun Spray Coating, of 347H Boiler Steel to Enhance its High Temperature Corrosion Resistance”, Mater. High Temp., accepted for publication.

19.    Otanicar, T. P., Phelan, P. E., Taylor, R. A., and Tyagi, H., 2011, "Spatially Varying Extinction Coefficient for Direct Absorption Solar Thermal Collector Optimization", ASME Journal of Solar Energy Engineering,  133(2), pp. 024501.  (doi: http://dx.doi.org/10.1115/1.4003679)

20. Maurya, R.K.,and Agarwal, A.K., "Effect of Start of Injection on the Particulate Emission from Methanol Fuelled HCCI Engine"  SAE International Journal of Fuels and Lubricants,Volume  4, Issue 2, pp, 204-222, 2011, SAE  2011-01-2408. (Print ISSN: 1946-3952; Online ISSN: 1946- 3960).

21. Maurya, R.K., Srivastava,D.K., and Agarwal, A.K.,March 2011 “Experimental investigations of particulate emitted by an alcohol fuelled HCCI/ CAI combustion engine,” International Energy Journal, Volume 12, Issue 1, March, 2011, pp 29-38, 2011. (ISSN# 1513-718X).

22. Maurya, R.K., and Agarwal, A.K., “Experimental Investigation on Intake Air Temperature and Air-Fuel Ratio Dependence of Random and Deterministic Cyclic Variability in Homogeneous Charge Compression Ignition Engine”, SAE 2011-01-1183, SAE Special Publication SP-2313, 2011. (ISBN # 978-0-7680-4752-3).

23. Maurya, R.K.,and Agarwal, A.K., “Experimental investigation on the effect of intake air temperature and air fuel ratio on cycle-by-cycle variations of HCCI combustion and performance
parameters,”  Applied Energy, Volume 88, Issue 4, pp 1153-1163, 2011. (ISSN # 0306-2619). (Impact Factor: 4.781)

24. Maurya, R.K., and Agarwal, A.K., "Experimental Study on the Combustion and Emission Characteristics of the Ethanol fuelled Port Injected Homogeneous Charge Compression Ignition (HCCI) Combustion Engine," Applied Energy, Volume 88, Issue 4, pp 1169-1180, 2011. (ISSN # 0306-2619). (Impact Factor: 4.781)

25. Satyamurty, V. V., and Ramjee, R., 2011 “Superposition Relations for Forced Convective Local Nusselt Numbers for Flow through Asymmetrically Heated Parallel Plate Channels”, Heat Transfer Engineering,  32(6), pp. 476-484.

26.   Shivamurthy, R. C., Surappa, M. K., 2011, "Tribological Characteristics Of A356 Al Alloy-SiCP Composite Discs", Wear, 271(9-10), pp.1946-1950.

27.    Singh, S., Kulkarni, K. V., Pandey, R. and Singh, H., 2012, “Buckling Analysis of Thin Rectangular Plates with Cutouts subjected to Partial Edge Compression using FEM”, Journal of Engineering, Design and Technology, 10(1), pp. 128-142.

28.    Singh, S., Pandey, R. and Singh, H., 2011, “Design and Performance Analysis of Hollow Helical Spring made from Isotropic Materials”, Journal of Engineering, Design and Technology, accepted for publication in Vol. 10, No. 01.

29.    Singla, M. K., Singh, H. and Chawla, V., 2011, “Thermal Sprayed CNT Reinforced Nanocomposite Coatings – A Review”, J. Minerals Mater. Charact. Eng.,10(8), pp.717-726.

30.  Varunkumar, S., Rajan, N. K. S., & Mukunda, H. S., 2011, "Single particle and packed bed combustion in modern gasifier stoves - density effects", Combustion Science and Technology, Vol. 183(11), pp. 1147-1163.

 

2010

1.   Ajith, M., R. Das, R. Uppaluri and S.C. Mishra, 2010, Estimation of boundary surface heat fluxes in a square enclosure with an embedded design element, AIAA-Journal of Thermophysics & Heat Transfer,  24 (4), pp. 845-849.

2.  Anilchandra, A. R., Surappa, M. K., 2010, "Influence of tool rake angle on the quality of pure magnesium chip-consolidated product", Journal of Materials Processing Technology, 210 (3), pp. 423-428.

3.  Arora, H.S., Bala, N. and Singh, H., 2010, “Wear Performance of Cold Spray Ni-20Cr Coating on T-22 and SA-516 Boiler Steels”, J. Tribology Surf. Eng., 1(3-4).

4.  Bala, N., Singh, H. and Prakash, S., 2010, “Accelerated Hot Corrosion Studies of Cold Spray Ni-50Cr Coating on Boiler Steels”, Mater. Design, Vol. 31, pp. 244-253.

5.  Bala, N., Singh, H. and Prakash, S., 2010, “High Temperature Corrosion Behavior of Cold Spray Ni-20Cr Coating on Boiler Steel in Molten Salt Environment at 900 °C”, J. Thermal Spray Technol., 19(1-2), pp. 110-118.

6.  Das, R., S.C. Mishra, and R. Uppaluri, 2010, Inverse analysis applied to retrieval of parameters and reconstruction of temperature field in a transient conduction-radiation heat transfer problem involving mixed boundary conditions, International Communications in Heat & Mass Transfer,  37 (1), pp. 52-57.

7.   Debnath, B. K., and R. Das, 2010, Prediction of performance coefficients of a three bucket Savonius rotor using artificial neural network, Journal of Renewable & Sustainable Energy, 02 (4), pp. 043107-1-10.

8.  Gill, S. S., Singh, J., Singh, H., and Singh, R., 2010, “Investigation on Wear Behaviour of Cryogenically Treated TiAlN Coated Tungsten Carbide Inserts in Turning”, Inter. J. Machine Tools & Manufacture, 10.1016/j.ijmachtools.2010.10.003.

9.  Gitanjali, Singh, H., Singh, S. and Prakash, S., 2010, “Effect of Superficially Applied Y2O3 Coating on High Temperature Corrosion Behaviour of Ni-Base Superalloys”, Metall. Mater. Trans. A, 27(2), pp. 109-116.

10.  Jayal, A. D., Badurdeen, F., Dillon, Jr., O. W., and Jawahir, I. S., 2010, “Sustainable Manufacturing: Modeling and Optimization Challenges at the Product, Process and System Levels,” CIRP Journal of Manufacturing Science and Technology, 2(3), pp. 144-152.

11.  Jayal, A. D., Umbrello, D., Dillon, Jr., O. W., and Jawahir, I. S., 2010, “An Investigation of the Effects of Cutting Conditions, Tool Edge Geometry and Workpiece Hardness on Surface Integrity in Orthogonal Machining of AISI 52100 Steel,” Transactions of NAMRI/SME, XXXVIII, pp. 57-64.

12.  Kaur, M., Singh, H. and Prakash, S., 2010, “Role of Detonation-Gun Spray Cr3C2-NiCr Coating in Improving High Temperature Corrosion Resistance of SAE-213-T22 and SAE-347H Steel in the Presence of Na2SO4-82%Fe2(SO4)3 Salt Deposits”, Surface Engineering, Vol. 26, No. 6, pp. 428-439.

13.  Kaur, M., Singh, H., Singh, B. and Singh, B., 2010, “Studies on the Sliding Wear Performance of Plasma Spray Ni-20Cr and Ni3Al Coatings”, J. Thermal Spray Technol., 19(1-2), pp. 378-383.

14.  Kumar, N., and Singh, S. P., Experimental Study on Vibration and Damping of Curved Panel Treated with Constrained Viscoelastic Layer, Composite Structures, 2010, 92, 233–243. (Elsevier Journal, Impact factor, 2.24).

15.  Phelan, P. E., Gupta, Y., Tyagi, H., Prasher, R., Cattano, J., Michna, G., Zhou, R., Wen, J., Jensen, M., and Peles, Y. , 2010, "Energy Efficiency of Refrigeration Systems for High-Heat-flux Microelectronics", ASME Journal of Thermal Science & Engineering Applications, Vol. 2, pp. 031004.  (doi: http://dx.doi.org/10.1115/1.4003041)

16. Prasad,R.M., Gurlo,A.,Riedel,R.,Hübner,M., Barsan,N., Weimar,U., “Microporousceramic coated SnO2 sensors for hydrogen and carbon monoxide sensing in harsh reducing conditions,” Sensors and Actuators B: Chemical,Vol. 149 (2010)pp.105-109

17. Prasad,R.M.,Iwamoto,Y., Riedel,R., Gurlo,A., “Multilayer amorphous-Si-B-CN/gamma-Al2O3/alpha-Al2O3 membranes for hydrogen purification,”  Advanced Engineering Materials,Vol 12 (2010) pp.522-528 (Cover Article)

18.  Ramjee, R., and Satyamurty, V. V., 2010, “Local and Average Heat Transfer in the Thermally Developing Region of an Asymmetrically Heated Channel”, Int. J. of Heat and Mass Transfer, Vol. 53, Nos. 9-10, pp. 1654-1665.

19.  Ramjee, R., and Satyamurty, V. V. , 2010, “Limiting Nusselt Numbers for Viscous Dissipative Flow between Parallel Plates Kept at Unequal Temperatures”, Int. Comm. in Heat and Mass Transfer, Vol. 37, pp. 1251-1254.

20.  Singla, E., Tripathi, S., Rakesh, V., and Dasgupta, B., 2010, “Dimensional synthesis of kinematically redundant serial manipulators for cluttered environments”,  Robotics and Autonomous Systems,  58 (5), pp. 585-595.

21.  Umbrello, D., Jayal, A. D., Caruso, S., Dillon, O. W., and Jawahir, I. S., 2010, “Modeling of White and Dark Layer Formation in Hard Machining of AISI 52100 Bearing Steel,” Machining Science and Technology, 14(1), pp. 128-147.

22.  Umbrello, D., Outeiro, J. C., M’Saoubi, R., Jayal, A. D., and Jawahir, I. S., 2010, “A Numerical Model Incorporating the Microstructure Alteration for Predicting Residual Stresses in Hard Machining of AISI 52100 Steel,” Annals of the CIRP, 59(1), pp. 113-116.

 

2009

1. Ajith, M., R. Das, R. Uppaluri and S.C. Mishra, 2009, Optimization of heat fluxes on the heater and the design surfaces of a radiating-conducting medium,   Numerical Heat Transfer:           Part A, Vol. 56 (10), pp. 846-860.

2. Bala, N., Singh, H. and Prakash, S., 2009, “High-temperature Oxidation Studies of Cold-sprayed Ni-20Cr and Ni-50Cr Coatings on SAE 213-T22 Boiler Steel”, Appl. Surf. Sci.,  255(15),       pp. 6862-6869.

3. Bauri, R., & Surappa, M.K., 2009, "Processing and Compressive Strength of Al-Li-SiCp Composites Fabricated by a Compound Billet Technique", Journal of Materials Processing                   Technology,  209(4), pp. 2077-2084.

4. Das, R., S.C. Mishra and R. Uppaluri, 2009, Retrieval of thermal properties in a transient conduction radiation problem with variable thermal conductivity, International Journal of Heat       & Mass Transfer, 52 (11-12), pp. 2749-2758.

5. Dasgupta, B., Gupta, A., and Singla, E., 2009, “A variational approach to path planning for hyper-redundant manipulators”,  Robotics and Autonomous Systems,  57 (2), pp 194-201.

6. Gill, S. S., Singh, H., Singh, R. and Singh, J., 2009, “Cryoprocessing of Cutting Tool Materials-A Review”, Int. J. Adv. Manuf. Technol.,  48(1–4), pp. 175–192.

7. Gill, S. S., Singh, R., Singh, H. and Singh, J., 2009, “Wear Behaviour of Cryogenically Treated Tungsten Carbide Inserts under Dry and Wet Turning Conditions”, Inter. J. Machine Tools       Manufacture, 49(304), pp. 256-260.

8. Jayal, A. D., and Balaji, A. K., 2009, “Effects of Cutting Fluid Application on Tool Wear in Machining: Interactions with Tool-coatings and Tool Surface Features,”  Wear, 267(9-10), pp.         1723-1730.

9. Kaur, M., Singh, H. and Prakash, S., 2009, “High Temperature Corrosion Studies of HVOF Sprayed Cr3C2-NiCr Coating on SAE-347H Boiler Steel”, J. Thermal Spray Technol., 18(4), pp.       619-632.

10. Kumar, N., Meena, S., Singh, S. P., and Nakra, B. C., Vibration control of plate with partially covered active constrained layer damping, 2009, Advances in Vibration Engineering, 4 vol.       8, 327-338.

11. Kumar, N., and Singh, S. P., Vibration and damping characteristics of beams with active constrained layer treatments under parametric variations, Materials and Design, 2009, 30,             4162–4174 (Elsevier Journal, Impact factor, 2.20).

12. Mishra, S. C., M.Y. Kim, R. Das, M. Ajith and R. Uppaluri, 2009, Lattice Boltzmann method applied to the analysis of transient conduction-radiation problem in a cylindrical medium,               Numerical Heat Transfer: Part A,  56 (1), pp. 42-59.

13. Maurya, R.K., and Agarwal, A.K., "Experimental Investigation of Effect of IntakeAir Temperature and Mixture Quality on Combustion of Methanol and Gasoline Fuelled HCCI Engine",
      Journal of Automobile Engineering, Proceedings of IMechE, Part-D, Volume 223, Number 11,pp 1445-1458, 2009. (ISSN # 09544070). (Impact Factor: 0.583)

14. Maurya, R.K. and Agarwal, A.K., "Experimental Investigation of cycle-by-cycle variations in CAI/HCCI combustion of Gasoline and Methanol by varying different engine operating
      conditions", SAE 2009-01-1345, SAE Special Publication SP-2242, 2009. (ISBN # 978-0-7680-2138-7).

15. Singh, H., Gitanjaly, Singh, S. and Prakash, S., 2009, “High Temperature Corrosion Behaviour of Some Fe-, Co- and Ni-base Superalloys in the presence of Y2O3 as Inhibitor”, Appl.           Surf. Sci., 255(15), pp. 7062-7069.

16. Tyagi, H., Phelan, P. E., and Prasher, R., 2009, "Predicted Efficiency of a Low-Temperature Nanofluid-Based Direct Absorption Solar Collector", ASME Journal of Solar Energy                         Engineering, Vol. 131(4), pp. 041004. [Appeared as 'Top 10 Most Downloaded Articles' of ASME JSEE during the months of Oct & Nov 2009].   

2008
1.  Agrawal, A., Reddy, N.V., Dixit, P.M. 2008 “Optimal Blank Shape Prediction Considering Sheet Thickness Variation: An Upper Bound Approach”, Journal of Materials Processing Technology, Volume 196, Issues 1-3, Pages 249-258.

2.  Das, R., S.C. Mishra and R. Uppaluri, 2008, Simultaneous reconstruction of thermal field and retrieval of parameters in a cylindrical enclosure, Numerical Heat Transfer: Part A, 54 (10), pp. 983-998.

3.  Das, R., S. C. Mishra, M.Ajith and R. Uppaluri, 2008, An inverse analysis of a transient 2-D conduction-radiation problem using the lattice Boltzmann method and the finite volume method coupled with the genetic algorithm, Journal of Quantitative Spectroscopy & Radiative Transfer,  109 (11), pp. 2060-2077.

4.  Das, R., S. C. Mishra, and R. Uppaluri, 2008, Multi-parameter estimation in a transient conduction-radiation problem using the lattice Boltzmann method and the finite volume method coupled with the genetic algorithms, Numerical Heat Transfer: Part A,  53 (12), pp. 1321-1338.

5.  Gitanjali, Singh, H. and Prakash, S., 2008, “Effect of Superficially applied ZrO2 Inhibitor on the High Temperature Corrosion Performance of Some Fe-, Co- and Ni-Base Superalloys”, Appl. Surf. Sci., 254(20), pp. 6653-6661.

6.  Kaur, M., Singh, H. and Prakash, S., 2008, “A Survey of the Literature on the Use of High Velocity Oxy-Fuel Spray Technology for High Temperature Corrosion and Erosion-Corrosion Resistant Coatings”, Anti Corros. Method M., 55(2), pp. 86-96.

7.  Mehandia, V., & Nott, P. R., 2008, "The Collective Dynamics of Self-Propelled Particles", Journal of Fluid Mechanics, Vol. 595, pp. 239-264.

8.  Singh, H., Grewal, M. S., Sekhon, H. S. and Rao, R. G., 2008, “Sliding Wear Performance of High-Velocity Oxy-Fuel Spray Al2O3/TiO2 and Cr2O3 coatings”, Proc. Instn Mech. Engrs, Part J: J. Engineering Tribology, Vol. 222, pp. 601-610.

9.  Singh, S., Singh, B. and Singh, H., 2008, “Design of an Adjustable Roller Chain Coupling for Shafts of different Diameters”, Inter. J. Applied Eng. Research, Vol. 3, No. 11, pp. 1581-1590.

10.  Tyagi, H., Phelan, P. E., Prasher, R., Peck, R., Lee, T. W., Pacheco, J. R., and Arentzen, P., 2008, "Increased Hot-Plate Ignition Probability for Nanoparticle-Laden Diesel Fuel", NanoLetters, Vol. 8(5), pp. 1410-1416. [Also highlighted in the Apr 30, 2008 issue of Chemical & Engineering News and in the May 2, 2008 issue of Nature (Nature Nanotechnology)].  (doi: http://dx.doi.org/10.1021/nl080277d)

2007
1.  Agrawal, A., Reddy, N.V., Dixit, P.M. 2007 “Determination of Optimum Process Parameters for Wrinkle Free Products in Deep Drawing Process”, Journal of Materials Processing                 Technology, 191(1-3), PP. 51-54.

2.  Bala, N., Singh, H. and Prakash, S., 2007, “An Overview of Characterisations and High Temperature Behaviour of Thermal Spray NiCr Coatings”, Inter. J. Mater. Sci., 2,(3), pp. 201–            218.

3.   Bala, N., Singh, H. and Prakash, S., 2007) “An Overview of Cold Spray Technique”, Mater. Sci. Forum, Vols. 561-565, pp. 2419-2422.

4.   Deep, K.S., Reddy, N.V., Agrawal, A., Ramkumar, J. 2007)“A Mathematical Model for Determination of Limiting Blank Holding Force and Cavity Pressure in Hydromechanical Deep                 Drawing”, Proc. IMechE, Part B: Journal of Engineering Manufacture, Volume 221, Pages 155-162.

5.   Jayal, A. D., Balaji, A. K., Sesek, R., Gaul, A., and Lillquist, D. R., 2007, “Machining Performance and Health Effects of Cutting Fluid Application in Drilling of A390.0 Cast Aluminum Alloy,”       Journal of Manufacturing Processes, 9(2), pp. 137-146.

6.   Kaur, M., Singh, H. and Prakash, S., 2007, “Some Observations regarding Erosion-Corrosion Performance of HVOF-Sprayed Cr3C2- NiCr and Cr3C2- NiCr-(25) WC-Co coatings in              Actual Boiler Environment”, Adv. Mater. Research, Vols. 26-28, pp. 1345-1348.

7.   Kaur, M., Singh, H. and Prakash, S., 2007, “Use of High Velocity Oxy-Fuel Spray Technology to Combat Hot Corrosion and Erosion-Corrosion of Materials”, Trans. Indian Inst. Met.,            60(6), pp. 587-597.

8.  Sidhu, B.S., Singh, H., Puri, D. and Prakash, S., 2007, “Wear and Oxidation behaviour of Shrouded Plasma Sprayed Fly Ash Coatings”, Tribology Inter., Vol. 40, pp. 800-808.

9.  Singh, H., Puri, D. and Prakash, S., 2007, “An Overview of Na2SO4 and/or V2O5 Induced Hot Corrosion of Fe- and Ni-based Superalloys,” Rev. Advanced Mater. Sci., 16(1-2), pp. 27-        50.

10.  Singh, H., Puri, D. and Prakash, S., 2007, “Some Observations on the High Temperature Oxidation behaviour of Plasma Sprayed Ni3Al Coatings”, Mater. Sci. Eng. A, 444(1-2), pp.              242-250.

11.  Singh, H., Puri, D., Prakash, S. and Ghosh, T. K., 2007, “Hot Corrosion of A Plasma Sprayed Ni3Al Coating on A Ni-Base Superalloy”, Mater. Corros., 58(11), pp. 857-866.

12. Singh, H., Puri, D., Prakash, S. and Hira, D.S., 2007, “Investigations on the Role of Plasma Sprayed NiCrAlY and Ni-20Cr Coatings to combat Hot Corrosion”, Mater. Sci. Technol.,                 23(6), pp. 736-744.

13.  Singh, H., Puri, D., Prakash, S. and Maiti, R., 2007, “Characterization of Oxide Scales to evaluate High Temperature Oxidation behavior of Ni-20Cr Coated Superalloys”, Mater. Sci.              Eng. A, 464(1-2), pp. 110-116.

14.  Singh, H., Sidhu, B.S., Puri, D. and Prakash, S., 2007, “Use of Plasma Spray Technology for deposition of High Temperature Oxidation/Corrosion Resistant Coatings -A Review”,                 Mater. Corros., 58(2), pp. 92-102.

2006
1.  Singh, H., Puri, D. and Prakash, S., 2006, “High Temperature Oxidation Behaviour of Plasma Sprayed NiCrAlY Coatings on Ni-Based Superalloys in Air”, Trans. Indian Inst. Met., Vol.            59, pp. 215-227.

2.  Singh, H., Puri, D., Prakash, S. and Rao V.V.R., 2006, “On the High-Temperature Oxidation Protection Behaviour of Plasma Sprayed Stellite-6 Coatings”, Metall. Mater. Trans. A, Vol.            37, pp. 3047-3056.

3.  Singh, H., Puri, D., Prakash, S. and Phase, D.M., 2006, “Cyclic Oxidation Behavior of some Plasma Sprayed Coatings in Na2SO4-60%V2O5 Environment”, J Mater. Eng. Perfor., 15(6),          pp. 729-741.

4.   Singh, H., Puri, D., Prakash, S. and Srinivas, M., 2006, “Characterisation of High Temperature Oxide Scales for Plasma Sprayed NiCrAlY coated Ni- and Fe-base Superalloys”, Anti               Corros. Method M., 53(5), pp. 283-295.

5.  Tyagi, H., Liu, R., Ting, D. S.-K., and Johnston, C. R., 2006, "Measurement of Wake Properties of a Sphere in Freestream Turbulence", Experimental, Thermal and Fluid Sciences, Vol. 30,      pp. 587-604.  (doi: http://dx.doi.org/10.1016/j.expthermflusci.2005.12.004)

2005
1.   Balaji, A. K., Varghese, V., and Jayal, A. D., 2005, “On the Wear of Coated Carbide Inserts in High-Speed Turning of AISI 1045 Steel,” Transactions of NAMRI/SME, XXXIII, pp. 557-             564.

2.   Prakash, S., Puri, D. and Singh, H., 2005, “Hot Corrosion Behaviour of Plasma Sprayed Coatings on a Ni-Based Superalloy in Na2SO4 -60%V2O5 Environment”, ISIJ Int., 45(6), pp.           886-895.

3.   Singh, H., Puri, D. and Prakash, S., 2005, “Corrosion Behaviour of Plasma Sprayed Coatings on a Ni-base Superalloy in Na2SO4-60%V2O5 Environment at 9000C”, Metall. Mater.               Trans. A, 36(4), pp. 1007-1015.

4.   Singh, H., Puri, D. and Prakash, S., 2005, “Some Studies on Hot Corrosion Performance of Plasma Sprayed Coatings on a Fe-Based Superalloy”, Surf. Coat. Technol., 192(1), pp. 27-         38.

5.   Singh, H., Puri, D. and Prakash, S., 2005, “Studies of Plasma Spray Coatings on a Fe-base Superalloy, their Structure and High Temperature Oxidation Behaviour”, Anti Corros.                 Method M.,52(2), pp. 84-95.